6.0 Resetting Home Roll and Pitch Instructions

Share this document
  • Last update: 03 July 2013

6.1 Resetting Home Pitch Default Position ONLY

If you experience a problem during the HOME PITCH CALIBRATION PROCESS and feel the resulting HOME PITCH DEFAULT POSITION is not accurate, you can erase the HOME PITCH DEFAULT POSITION from TEST MODE. You must first erase the HOME PITCH DEFAULT POSITION before you can re-enter the HOME PITCH CALIBRATION PROCESS and allow the AUTO GLIDE to learn a new HOME PITCH DEFAULT POSITION.

NOTE: HOME ROLL DEFAULT POSITION will not be affected when you erase the HOME PITCH DEFAULT POSITION. Section 6.2 will explain how to erase the HOME ROLL DEFAULT POSITION.

The following illustrations outline how to erase the HOME PITCH DEFAULT POSITION from TEST MODE.

1. ACTIVATE TEST MODE:

With your motor(s) turned “OFF”, activate TEST MODE from STANDBY MODE by pressing and holding all four (4) UP/DN buttons on the Key Pad for four (4) seconds.

2. VERIFY TEST MODE ACTIVATION:

Once TEST MODE is activated, the LEDS on the key pad run through a sequence of flashes to notify the operator that the Auto Glide is in TEST MODE. The following illustrations outline this sequence of LED flashes signifying the Auto Glide is in TEST MODE:

3. ERASING HOME PITCH DEFAULT POSITION:

Once the Auto Glide is in TEST MODE, press and hold the “HOLD” AUTOMATIC SETTING button until the “HOLD” LED INDICATOR flashes three times. The three flashes of the “HOLD” LED INDICATOR confirms that the HOME PITCH DEFAULT POSITION has been erased.

4. EXIT TEST MODE:

After erasing the HOME PITCH DEFAULT POSITION, you must exit TEST MODE before you can re-enter the HOME PITCH CALIBRATION MODE. Exit TEST MODE by holding down all four (4) UP/DN buttons for one (1) second. The AUTOMATIC SETTING LED INDICATORS will go blank indicating the Auto Glide is back in STANDBY MODE.

5. RESET HOME PITCH DEFAULT POSITION:

Restart your motor(s) and the Auto Glide will default to HOME PITCH CALIBRATION MODE. The VERTICAL CROSSHAIR LED INDICATORS will scroll up and down to indicate the Auto Glide is ready to reset a new HOME PITCH DEFAULT POSITION.

Return to page 17 of this manual for HOME PITCH SETUP INSTRUCTIONS and follow the instructions to set the new HOME PITCH DEFAULT POSITION.

 

6.2 Resetting Home Roll and Home Pitch Default Positions

If you need to reset the HOME ROLL DEFAULT POSITION, you will also need to erase and reset the HOME PITCH DEFAULT POSITION. The Auto Glide erases both HOME ROLL AND HOME PITCH DEFAULT POSITIONS when you erase the HOME ROLL DEFAULT POSITION. Even if you only want to erase the HOME ROLL DEFAULT POSITION, the Auto Glide will automatically erase the HOME PITCH DEFAULT POSITION.

The following instructions explain how to erase and reset both HOME ROLL AND HOME PITCH DEFAULT POSITIONS.

1. ACTIVATE and VERIFY TEST MODE:

SEE STEPS 1 & 2 ON PAGE 20

2. ERASING HOME ROLL AND PITCH DEFAULT POSITION:

Once the Auto Glide is in TEST MODE, press and hold the “AUTO” AUTOMATIC SETTING button until the “AUTO” LED INDICATOR flashes three times. The three flashes of the “AUTO” LED INDICATOR confirm that both the HOME ROLL AND PITCH DEFAULT POSITIONS have been erased.

NOTE: IF YOU DO NOT RESET THE HOME ROLL DEFAULT POSITION BEFORE EXITING TEST MODE, THE AUTO GLIDE WILL AUTOMATICALLY RESAVE THE PREVIOUS HOME ROLL DEFAULT POSITION WHEN YOU EXIT OUT OF TEST MODE. 

3. RESET HOME ROLL DEFAULT POSITION:

Once the Auto Glide is in ROLL CALIBRATION MODE, you will need to reset the HOME ROLL DEFAULT POSITION

by pressing and releasing the “AUTO” Automatic button.

NOTE: SETTING AN ACCURATE HOME ROLL DEFAULT POSITION IS VERY IMPORTANT TO THE PERFORMANCE OF THE AUTO GLIDE. LENCO MARINE RECOMMENDS SETTING THE HOME ROLL DEFAULT POSITION IN SMOOTH WATER CONDITIONS. IF THE BOAT IS ROCKING BACK AND FORTH WHEN THE HOME ROLL DEFAULT POSITION IS CALIBRATED, THE HOME ROLL POSITION MAY BE SLIGHT SKEWED TO PORT OR STARBOARD.

4. CONFIRMATION NEW HOME ROLL DEFAULT POSITION HAS BEEN SAVED:

Once you release the “AUTO” AUTOMATIC SETTING button the “AUTO” LED INDICATOR will flash three times. The three flashes of the “AUTO” LED INDICATOR confirm that the new HOME ROLL DEFAULT POSITIONS has been stored. The HORIZONTAL CROSSHAIR LED INDICATORS will also stop scrolling to indicate the Auto Glide has exited out of HOME ROLL CALIBRATION MODE and has defaulted back into TEST MODE.

5. EXIT TEST MODE:

After erasing the HOME PITCH DEFAULT POSITION, you must exit TEST MODE before you can re-enter the HOME PITCH CALIBRATION MODE. Exit TEST MODE by holding down all four (4) UP/DN buttons for one (1) second. The AUTOMATIC SETTING LED INDICATORS will go blank indicating the Auto Glide is back in STANDBY MODE. SEE ILLUSTRATION ON PAGE 21.

6. RESET HOME PITCH DEFAULT POSITION:

Restart your motor(s) and the Auto Glide will default to HOME PITCH CALIBRATION MODE. The VERTICAL CROSSHAIR LED INDICATORS will scroll up and down to indicate the Auto Glide is ready to reset a new HOME PITCH DEFAULT POSITION.

Return to page 15 of the HOME ROLL AND PITCH SETUP INSTRUCTIONS and follow the instructions to set the new HOME PITCH DEFAULT POSITION.

 

END OF OWNER’S MANUAL A

Refer to Owner’s Manual B for Operational Instructions

Comments (0)

Leave a comment

You are commenting as guest.