Each kit contains:
- Electro-polished stainless steel trim tab blades (2)
- Heavy Duty and Extreme Duty Kits come pre-assembled with electro-polished stainless steel back plates and gland seal (2)
- Standard or Heavy Duty actuators with 6' lead & deutsch plugs (2)
- 20' actuator extension wiring harnesses (2) except for Extreme Duty kits which are sold seperately in lengths of 7', 14', 20', 26' and 32'
- Upper mounting bracket with gland seal (2) (standard series only)
- Lower mounting bracket-#119 (standard series only) (2)
- All necessary mounting hardware (standard series only, customer supplied hardware on all others)
- Switch sold separately, dual actuator kits must use
-
Switch sold separately, dual actuator kits must use switch #15071-001(123DRSC)
In the part description:
- RT = Performance Tab
- First number represents the tab length
- Second number represents tab width at hinge
- NS = No Switch
Standard Duty
Standard actuator with 5/16" (.79 cm) stainless steel through bolts. 1" (2.54 cm) turned up edges with 2" (5.08 cm) taper on the inside. All 12-gauge (2.6 mm) 304 electro-polished stainless steel blades and hinges.
Standard Tabs Part Numbers
(Superceded Number)
#15034-101 (RT 9x9 NS)
#15035-101 (RT 9x12 NS)
#15036-101 (RT 12x9 NS)
#15037-101 (RT 12x12 NS)
#15038-101 (RT 14x12 NS)
#15039-101 (RT 16x12 NS)
#15040-101 (RT 18x14 NS)
|
 |
Heavy Duty
12" x 12" HDNS (30.48 x 30.48 cm)
16" x 12" HDNS (40.64 x 30.48 cm)
18" x 14" HDNS (45.74 x 35.56 cm)
Extreme-duty actuators with 316 stainless steel billet ram. 1" (2.54 cm) turned up edges with 2" (5.08 cm) taper on the inside. Full transom back plate and adjustable C channel mounting brackets with 5/16" (.79 cm) stainless steel mounting studs. All 12-gauge (2.6 mm) 304 electro-polished stainless steel blades with 3-3/4" (9.53 cm) zinc anodes. Gland seal/strain relief through backplate.
Heavy Duty Tabs Part Numbers
(Superceded Number)
#15041-101 (RT 12x12 HDNS)
#15043-101 (RT 16x12 HDNS)
#15044-101 (RT 18x14 HDNS)
All HD racing tabs are 12-gauge (2.6 mm) electro-polished stainless steel
Extreme Duty
17" x 12" XDNS (43.18 x 55.88 cm)
Extreme-duty actuators with 316 stainless steel billet end.
19" x 14" XDNS (48.26 x 35.56 cm)
24" x 14" XDNS (63.5 x 35.56 cm)
Dual extreme-duty actuators with 316 stainless steel billet end.
1" (2.54 cm) turned up edges with 2" (5.08 cm) taper on the inside edge. Full transom back plate and adjustable C channel mounting brackets with 3/8" (.95 cm) stainless steel mounting bolts and 3/8" (.95 cm) diameter hinge pin. All 10-gauge (3.4 mm) 304 electro-polished stainless steel blades with 3-3/4" (9.53 cm) zinc anodes. Gland seal/strain relief through backplate.
Extreme Duty Part Numbers
(Superceded Number)
#15045-101 (RT 17x12 XDNS)
#15046-101 (RT 19x14 XDNS, dual actuator)
#15047-101 (RT 24x14 XDNS, dual actuator)
|
|
